ASTM B153 PDF

B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering

Author: Miktilar Grocage
Country: Nepal
Language: English (Spanish)
Genre: Education
Published (Last): 6 July 2006
Pages: 243
PDF File Size: 3.83 Mb
ePub File Size: 7.87 Mb
ISBN: 679-4-16203-283-5
Downloads: 62426
Price: Free* [*Free Regsitration Required]
Uploader: Mezijind

The tension test for other sizes of b513 need not be made except when indicated by the purchaser at the time of placing the order. Rockwell hardness tests shall be made on the inside surface of the tube. Rectangular including square tubes shall normally be supplied only in drawn general-purpose temper.

Any evidence of leakage shall be cause for rejection. Tubes shall be passed through an eddy-current test unit adjusted to provide information on the suitability of the tube for the intended application.

When there is a need for light-drawn or hard-drawn tempers these are to be supplied xstm agreed upon between the manufacturer and the purchaser.

Workmanship, Finish, and Appearance The manufacturer shall select the nondestructive test that is most suitable for the tube size and the application. Light-drawn bending temper is used only when a tube of some stiffness but yet capable of being bent is needed.

  LOS AVENTUREROS HAROLD ROBBINS PDF

List of ASTM International standards

Standard Specification for Silicomanganese. For these tubes, the mercurous nitrate test shall be required and nondestructive testing shall not be required. The notchdepth tolerance shall be Except as otherwise speci?

By using this site, you agree to the Terms of Use and Privacy Policy. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. However, if subsequent testing by the purchaser establishes that the material does not meet these requirements, the material astj be subject to rejection.

Alternatively, if the manufacturer uses speed-insensitive eddy-current units that are equipped so that a fraction of the maximum unbalance signal is able to be selected, the following percent maximum unbalance signals shall be used.

This standard adtm been approved for use by agencies of the Department of Defense. Grossman the Grossman method. Standard Specification for Steel Track Spikes. Former soft anneal soft anneal light anneal light anneal soft anneal soft anneal light anneal light anneal soft anneal soft anneal up to 0.

Rockwell hardness shall be made on the inside surface of the tube.

  INFOCUS IN112I PDF

Standard Specification for Pearlitic Malleable Iron. Ten alloys are speci? Standard Specification for Nickel Oxide Sinter.

ASTM B Specifications List – Colorado-Metallurgical-Services

Standard Specification for Molybdenum Oxide Products. Standard Tube Size, inch Up to and including 3? Tension tests are required for tubes with a wall thickness under 0. Retrieved from ” https: Standard Specification for Steel, Strip, Carbon 0.

بانك استانداردهاي گاز

The purchaser shall have the option to specify either a hydrostatic test in A Alloy Designations of Speci? Standard Specification for Ferrochromium. Screening and resubmittal of samples from rejected lots for visual and dimensional examination is acceptable. Hard-drawn temper is used only where there is need for a tube as strong as is commercially feasible for the sizes indicated.

For rectangular including square tubes see 5. Users of this standard are expressly advised that determination of the validity of any such asm rights, and the risk of infringement of such rights, are entirely their own responsibility.

Limits for unnamed elements are to be established by agreement between manufacturer or supplier and purchaser. Incomplete lists from February