Testing per ASTM D allows both the material engineer and the design engineer to test materials for desired properties such as strength, ductility, toughness. ISO – ASTM D Quick impact at low temperature. Instron Logo. β€œIt is our objective at Instron to provide our customers the best ownership experience by. This standard is issued under the fixed designation D ; the number immediately following fication System D lists the ASTM materials standards that.

Author: Akigore Yozshujin
Country: Grenada
Language: English (Spanish)
Genre: Spiritual
Published (Last): 20 December 2015
Pages: 296
PDF File Size: 18.21 Mb
ePub File Size: 15.62 Mb
ISBN: 641-5-58448-364-2
Downloads: 59717
Price: Free* [*Free Regsitration Required]
Uploader: Meshura

ASTM D High-Speed Puncture Properties of Plastics – Instron

For testing involving extremely tough materials, it may be necessary to locate the transducer further from the impact point to prevent damage. Due to copyright restrictions, we are not able to provide copies of standards.

Photographic or optical systems can also be utilized for measuring displacement. Link to Active This link will always route to the current Active version of the standard. No other units of measurement are included in this standard.

This test method further provides a measure of the rate sensitivity of the material to impact. This is especially true of plastics where many variables can affect the material.

Email addresses can only contain letters, numbers and the following special characters: The loaddisplacement recordings may also display signals or artifacts that are the result of physical or electrical contributions from the test device. Repair Services and Parts.

  AFI 36-2606 PDF

Numerous data values related to toughness and total energy are calculated including maximum force, energy at maximum force and total energy to break. Due in part to its unique capability to be manufactured to meet very specific, functional needs, plastic is the most used material in the world. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Two and a half additional hours were needed to reach equilibrium.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM D – Instron

The instrumented impact tester includes a thermal chamber that allows testing of specimens at elevated and reduced temperatures without the need to transfer asm specimens from an oven or freezer just prior to testing.

The High Speed Impact test is used to determine toughness, load-deflection curves and total energy absorption of impact events.

A percent drop in load from the peak is one type of criteria used. Software for Series Systems.

A thermocouple may be placed at the center of a xstm stack in which its height is equal to its minimum width. After the specimens have been cut, randomly order specimens. Since many materials especially thermoplastics exhibit lower impact strength at reduced temperatures, it is sometimes appropriate to test materials at temperatures that simulate the intended end use environment. Therefore, it is advisable to refer to that material specification before using this test method.


Five laboratories used falling weight machines and? Correlations between various geometries have not been established. This test configuration is well suited for determining the performance characteristics of plastic materials under impact conditions.

This provides better control and consistency of test results at non ambient temperatures. Cut the aluminum sheet into specimens of size by by 0.

ASTM D3763 High-Speed Puncture Properties of Plastics

Subscribe to Our Newsletters. Please confirm that you agree with our privacy and cookies e3763 to submit this form. Environmental chamber use allows both parties to get an understanding of how the material may perform in colder or warmer applications. A set of specimens are moved from the freezer to the chamber and one specimen is axtm onto the testing platform. How can we help you? Therefore, it is advisable to refer to that material specification before using this test method.

ASTM D3763 Puncture Resistance Fixture | GD3763-174

Dynamic failures of materials are different than those found when testing at slower, steadier speeds. How can we help you? Since the s, plastics have become a major industry β€” one that affects all aspects of our lives β€” providing improved packaging, creating new textiles, and permitting the production of new products and astmm technologies.