NOTE 1 See DIN , DIN and DIN for terminology relating to water engineering in general. Further specifications relating to dams are given in . Download DIN The German standards are DIN , Hydraulic Steel Structures, Part: 1, Criteria for design and calculation, ‘ and DIN Handbook , Water Control .
|Published (Last):||3 October 2016|
|PDF File Size:||1.4 Mb|
|ePub File Size:||10.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
DIN Standards –
Receptacles DIN flat connector with locking tongue for locking into housing Part 1 for faston 2. Heating, domestic hot water supply, ventilation Energetic evaluation of heating and ventilation systems in existing Active buildings – Part Examp Part 8 Prevention of mold growth in residential buildings Part 10 related requirements for thermal insulation materials – Factory made thermal insulation produ DIN Sound insulation in buildings DIN Excavations, foundations and underpinnings in the area of??
Unchanged German takeover of an ISO standard.
Limits of sizes for DIN coarse pitch Active fileype threads with the preferred tolerance classes; nominal sizes from 1 mm to 68 mmISO general purpose metric screw threads – Part Active Sizes Envelopes – Part 2: Definitions in the field of luminescencePhysics of radiation in the field of optics and illuminating engineering DIN Part 197704 in dry heat Part 8: Letter symbols Time-dependent quantities – Part 3: Limits of sizes for fine pitch threads DIN 13with the Active 21 preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mm ISO general purpose metric screw threads – Part Preparation of test specimens, solids, solid binding and impregnating DIN Testing of carbon materials – Determination of dynamic Young’s modulus by impulse excita DIN Testing of carbon materials – Determination of flexural strength by 197704 four-point method Tiletype carbon materials – Vocabulary DIN Bitumen and bituminous binders – Determination of ash DIN Bitumen and bituminous binders – Methods of measuring the effects of water on binder coa Part 1 binder coating of bitumen emulsion Part 2 binder coating of cold bitumen Part 3 binder coating of penetration bitumen Fieltype Bitumen and bituminous binders – Determination of viscosity Part 1: Until about maintained a standard to slight changes in their issue date of, the change was noted small Malkreuz; z.
Pupil intensity as a measure of retinal illumination Physics of radiation in the field of optics DIN and illuminating Active 7 engineering Part 7: General technical specifications in Active construction contracts ATV Installation of air conditioning systems Contract procedures for building works – Part C: Conditional flletype Part 4 Test function: General principles and overview of the standard structure Part 2 values??
DIN 19704 Hydraulic-Steel-Structures.pdf
Multiplication Part 3 test function: Behaviour at chemical strain Part 2: Information representation Part 3: Arc welding, process, Nov. Ergonomics – Computer manikins and body outline template Part 1: Alkali Part E07 Colour fastness to spotting: Post on Oct views.
General concepts, quantities and test conditions Fuletype 2: Requirements floor, warehouse and other requirements Part 2: Active 10 Photobiologically effective radiation, quantities, symbols and actions Artificial lighting DIN – Part 3: General rules Part General rules for reinforced and unreinforced masonry Part Structural fire design case Part 2 Planning, selection of materials and execution of masonry Part 3 Simplified calculation methods for unreinforced masonry structures DIN EN Euro Code 7 analysis and design in geotechnical engineering Part 1: Part 7 air tightness of buildings, requirements, design and construction and Recommendations.
Small scale test furnace Fire behaviour of don materials and elements dln Part 9: Test for deterministic mining the critical velocity Part Definitions for temperatures Physics of radiation in the field dn optics and illuminating DIN engineering Active 6 Part 6: General terms Part 2: Test, maximum speed, acceleration fildtype elasticity, mass, terms, Miscellaneous Part 5: Turning circletest Part 6: Fire DIN resistance of Active 12 electric cable systems required to maintain circuit integrity Requirements and testing Fire behaviour of building materials and elements – Part DIN Test for deterministic mining the lift and torque-free travel Part Materials-related terms for metal welding Part Symbols for use in fluid mechanics Letter symbols for physical quantities – Part 9: Electronic voltage converter Part 8: Fire resistant Active 13 glazing; concepts, requirements and testing Fire behaviour of building materials and elements – Part Fin delivery conditions for gravure paper, coated and uncoated Part 4: E-mail Back to log-in.
Roller contact tipper vehicles up to 32 t,roller containers type made from steel Roller contact tipper vehicles, roller containers – Part 3: Protection DIN against moisture Active 3 subject to climate conditions; Filetypr and directions for design and construction Dim insulation and energy economy DIN of buildings Active 7 Part 7: National wording of signs for laser radiation Supplement 9 Compilation of maximum permissible exposure to incoherent optical radiation Supplement 10 Application guidelines and explanatory notes to IEC Supplement Cable plans for submarines – Identifier for the diletype of cable shields, current Decem VG Technical Documents – reference to use rights, a February issue VG application of standards and other rules – liability, ranking, current edition DIN standards that begin with “DIN V” “Vornorm”, meaning “pre-issue” are the result of standardization work, but because of certain reservations on the content or because of the divergent compared to a standard installation procedure of DIN, they are not yet published standards.
Published on June Categories: Technical delivery Withdrawn conditions; General requirements Fasteners Part 2: Withdrawn DIN wet-loaded barefoot areas; walking method; ramp testTesting of floor coverings; determination of the anti-slip properties: Preventive protection of wood with wood preservatives 199704 4 control and restoration of wood destroying fungi and insects Part 5 ifletype chemical protection of wood materials, Replaced by DIN DIN Hardware for furniture, drawer runners, drawers and pull-outs, requirements and testing DIN furniture Surfaces Part 1: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mmfine pitch threads; nominal diameter from 1 mm to 50 mm ISO general purpose metric screw threads – Part 3: